Type R Club of America

I just replaced mine using the part numbers off an oem parts site/dealer direct. The new bolts I put on the ABS bracket were definitely not the same as what I took out.

The ones that came for the bottom I used for the side since it had the large washers and used the smaller ones on the bottom as you did.

What I would like to have done was find a local place to do the zinc plating but there isn't one.

Shoulda left that ABS stuff out

This is what the dealer provides, I can't say if they are the same as the original in terms of shape and size.

Looking good in here! Will I see you Sunday at Bridgewater?

Yes stin in correct with the bolts. I have the part numbers for the correct hardware in my thread. But like Stin received, I ordered all 3, 2 of which came silver and one semi yellow zinc.

So since the BNIB harness I was going to buy sold the day before I went to purchase, I need to clean up one of the OBD2a harness I have. Years of dirt and grime had the harness looking tired, so I peeled all of the electrical tape off where it was covering any wires and cleaned up all the plugs. Still going to do a final cleaning on each plug once I get some better cleaning tools, but she is all taped back up and clean again. Should look pretty spiffy once it's on the engine and back in the caR!






I also started with the firewall harnesses cleaning them up, re-taping and checking each connection. I think once I get them all cleaned up I'm going to dab them all with some dielectric grease so everything is nice nice.

That must have been such a pain in the ass. Looks good

Harness looks great Dan.

What are you doing with the other OBD2a ITR harness? I’m in need.

Sp00nFedFilms wrote: ↑Fri Aug 02, 2019 10:27 amHarness looks great Dan. What are you doing with the other OBD2a ITR harness? I’m in need.

Thank you sir! I'm keeping the others I have. I already sold one and regretted it as soon as I left the post office. LOL

RTW DC2R wrote: ↑Fri Aug 02, 2019 8:14 amThat must have been such a pain in the ass. Looks good

Thanks m8

It wasn't as bad as I thought tbh. Plus this is def a visibly rewarding task so once I got going, I was in the zone!

Dc2-ProductionS wrote: ↑Fri Aug 02, 2019 8:04 am So since the BNIB harness I was going to buy sold the day before I went to purchase, I need to clean up one of the OBD2a harness I have. Years of dirt and grime had the harness looking tired, so I peeled all of the electrical tape off where it was covering any wires and cleaned up all the plugs. Still going to do a final cleaning on each plug once I get some better cleaning tools, but she is all taped back up and clean again. Should look pretty spiffy once it's on the engine and back in the caR!






I also started with the firewall harnesses cleaning them up, re-taping and checking each connection. I think once I get them all cleaned up I'm going to dab them all with some dielectric grease so everything is nice nice.

What did you use to clean everything on that harness? That is a beautiful sight . Where was the new harness for sale?

Stin1 wrote: ↑Wed Aug 07, 2019 12:14 amWhat did you use to clean everything on that harness? That is a beautiful sight . Where was the new harness for sale?

Thanks! I took a good 10 mins and just looked at it myself when I was all done. LOL... I sprayed brake cleaner on a rag and wiped down the outsides of the plugs and connections. Then used a soft bristle brush to clean the outsides of the plugs. I still need to go back and do a "final" cleaning and then a touch of dielectric grease before install but was enough to re-tape everything else for now.

I peeled all the old tape off, gave a cleaning to what was underneath with some simple green spray and a rag, and then retaped nice nice.

The BNIB harness was for sale from a individual parts dealer on Instagram. Was posted for over a month, and the day I go to send payment he tells me he just sold it the night prior. I was so upset. Partially because there was no reason to not buy it when it was listed for sale. I was having trouble justifying the price, ( ) but now I'm kicking myself in the d!ck. All good though! It will be just as good when I'm done, it will just have a faded label tag instead of brand new.