Page 29 of 56

Re: 98-940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 1:26 pm
by Stin1
Updates on the daily. At least the next thing on it. Just like the integra as mentioned earlier in the thread there was a uninvited guest at some point it's life. Go figure huh?
IMG_3186.jpg
IMG_3186.jpg (330.14 KiB) Viewed 1891 times
IMG_3187.jpg
IMG_3187.jpg (210.19 KiB) Viewed 1891 times
This guy did more damage to the seal and nothing to the roof pillar like the Acura had done. I acquired the sub seal as Honda and Acura call it. These aren't the greatest to install. I never even found anything in the fsm about installing them, although I could be looking in the wrong place. Acura took a few tries to get the right part on the integra. Knowing Acura called it a sub seal I was successful on try one with the EM1
IMG_3188.jpg
IMG_3188.jpg (345.85 KiB) Viewed 1891 times

Re: 98-940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 1:39 pm
by Stin1
Next update is on the snatchback . I don't think I ever have posted much on it. Anyway when I purchased the integra I robbed peter to pay Paul for the integra. I took the seats I had that were in much better condition for the integra. I also took the ctr momo wheel and bought a dc2 hub to make it fit. The civic then went from being clean to having cig burned seats that were just not up to par. I traded them for some gsr seats plus some $ that were in better condition. My dad always called the car the silver bullet and would come out to see it even when he was sick before he passed. So I had to pay peter back! I wanted to clean them but I made it a point to have them installed by Father's Day.
IMG_3162.jpg
IMG_3162.jpg (164.49 KiB) Viewed 1891 times

Re: 98-940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 1:54 pm
by Stin1
I wanted USDM seats. I considered the jdm seats but I am a little to big in my opinion on drives for them. I would say they are perfect for the track, which I can't do with back injuries. I ended up with the mystery jdm seats that resemble type r seats. I would have been pretty disappointed if I bought them for the integra because they aren't the right market. On the civic totally cool! I get a pretty fresh driver seat, in terms bolster wear . The difference on the left side is that is has a rear pocket. My old seats had a similar decal, but I don't recall the name.
IMG_3035.jpg
IMG_3035.jpg (322.89 KiB) Viewed 1891 times

Re: 98-0940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 1:56 pm
by Stin1
IMG_3031.jpg
IMG_3031.jpg (294.71 KiB) Viewed 1891 times

Re: 98-0940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 1:58 pm
by Stin1
IMG_3167.jpg
IMG_3167.jpg (135.78 KiB) Viewed 1891 times

Re: 98-0940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 2:06 pm
by Stin1
I have never figured the origin of these seats other than being from Japan. They are identical in material. The right side of the right seat has one knob. It lowers the right bolster only. I think the rails are for a four door. One side of the rails have no wire cable or provisions that connect the rails.
IMG_3036.jpg
IMG_3036.jpg (153.55 KiB) Viewed 1891 times
IMG_3164.jpg
IMG_3164.jpg (205.69 KiB) Viewed 1891 times

Re: 98-0940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 2:09 pm
by Stin1
IMG_3173.jpg
IMG_3173.jpg (166.31 KiB) Viewed 1891 times
I made the Father's Day deadline.

Re: 98-0940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 3:13 pm
by Stin1
These are different. No lever. *** these are not my pictures.

Re: 98-0940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 3:15 pm
by Stin1
IMG_3193.jpg
IMG_3193.jpg (68.04 KiB) Viewed 1887 times
IMG_3194.jpg
IMG_3194.jpg (67.24 KiB) Viewed 1887 times

Re: 98-0940 Anyone know anything about the caR?

Posted: Mon Jun 17, 2019 3:21 pm
by Stin1
A mystery seat set for sale.