Page 50 of 56
Re: 98-0940 Anyone know anything about the caR?
Posted: Sun Oct 06, 2019 6:11 pm
by Stin1
Screw you !!!!!
- IMG_4327.jpg (268.72 KiB) Viewed 1635 times
This is what Acura provided for my cup / cubby hardware. This is what I think spoon received as well. This is the screw behind the door panel. Not only is it the wrong color for the cubby, and no washer, the threads are different.
Re: 98-0940 Anyone know anything about the caR?
Posted: Sun Oct 06, 2019 7:10 pm
by Stin1
- IMG_4323.jpg (122.27 KiB) Viewed 1632 times
New weatherstripping
Re: 98-0940 Anyone know anything about the caR?
Posted: Mon Oct 07, 2019 6:34 pm
by Stin1
I think I figured it out.
- IMG_4330.jpg (145.1 KiB) Viewed 1619 times
There's two pockets pictured in the parts diagram. The lower pocket should be pictured as a bracket for the pocket. The top one is the cup and screw.
Re: 98-0940 Anyone know anything about the caR?
Posted: Mon Oct 07, 2019 7:06 pm
by Stin1
Can someone confirm what the original screw should look like?
Re: 98-0940 Anyone know anything about the caR?
Posted: Wed Oct 30, 2019 11:57 pm
by Stin1
Happy Halloween ! The great pumpkin handed me this for 2019.
- IMG_4574.jpg (130.88 KiB) Viewed 1577 times
- IMG_4573.jpg (120.91 KiB) Viewed 1577 times
Re: 98-0940 Anyone know anything about the caR?
Posted: Thu Oct 31, 2019 5:23 pm
by coolhandluke
Those are impressive cuts.
Stin1 wrote: ↑Sun Oct 06, 2019 6:00 pm
The 98 has been without door panel for at least 2 months or more. The vapor seal went in on the driver side. I used this tape instead of the nasty butyl glue. IMG_4324.jpgIMG_4326.jpg
Where did you purchase this tape? I am about to run through this process.
Re: 98-0940 Anyone know anything about the caR?
Posted: Thu Oct 31, 2019 5:38 pm
by Stin1
coolhandluke wrote: ↑Thu Oct 31, 2019 5:23 pm
Those are impressive cuts.
Stin1 wrote: ↑Sun Oct 06, 2019 6:00 pm
The 98 has been without door panel for at least 2 months or more. The vapor seal went in on the driver side. I used this tape instead of the nasty butyl glue. IMG_4324.jpgIMG_4326.jpg
Where did you purchase this tape? I am about to run through this process.
I got it at oreillys but google seemed to show Walmart and every auto store had it too .
Re: 98-0940 Anyone know anything about the caR?
Posted: Thu Oct 31, 2019 8:02 pm
by 330R
The door pull pocket uses a black tapping screw (90101-S03-000)
The door pocket at the bottom of the door consists of two pieces and is attached with two screws (93913-14220) installed behind the door lining.
Re: 98-0940 Anyone know anything about the caR?
Posted: Thu Oct 31, 2019 8:15 pm
by Stin1
330R wrote: ↑Thu Oct 31, 2019 8:02 pm
The door pull pocket uses a black tapping screw (90101-S03-000)
The door pocket at the bottom of the door consists of two pieces and is attached with two screws (93913-14220) installed behind the door lining.
Thanks for that! Mark said that you checked and confirmed no washer on the black screw for the pocket correct? I didn't even think of that lower pocket.
Re: 98-0940 Anyone know anything about the caR?
Posted: Fri Nov 01, 2019 3:41 am
by 330R
Hmm I didn’t speak with spoonfed about it. But that’s correct, no washer on the black screw. I haven’t had a Teg door panel off in years so can’t remember what the bottom pocket screws look like... probably like the silver screw pictured above, just different part number.